Construction

How to make a flannel-lined zip-up hoodie

· 4 min read

Ask the factory to line both the body and the hood with the checked fabric, because a hood-only lining shows just a little check around the neck while a body lining gives the full layered look.

On this page
  1. How is a flannel-lined hoodie made?
  2. Why does the check still show when the hoodie is zipped?
  3. Should I line just the hood or the body as well?
  4. Do the sleeves need to be lined too?
  5. What changes when a hoodie has a lining?
  6. How do I brief a factory for a lined hoodie?

How is a flannel-lined hoodie made?

It is a zip-up hoodie with a second fabric sewn inside it. The outside is the usual sweatshirt fabric; inside, a separate checked lining runs through the body and up into the hood, so it looks as if a shirt is being worn underneath.

The look is a layering effect built into the construction. Nobody is wearing two garments: the checked fabric is part of the hoodie itself. That matters for a brand because it makes the effect repeatable. Every piece in the run shows the check in the same place, the customer does not have to style it, and the garment reads the same way each time it is opened or closed.

A lining is cut from its own pattern pieces and joined to the shell along the edges, such as the zip opening, the hood opening and the hem. How it finishes at the cuffs depends on whether the sleeves are lined, which is a separate decision covered below.

Why does the check still show when the hoodie is zipped?

Because the lining carries up into the hood. With the zip closed, the inside of the hood frames the face and neck, so the check stays visible at the opening even when the body is covered.

Opening the zip changes the whole look. The two fronts fall back and the checked lining shows down the full length of the body, which is what produces the layered effect. A good design uses both states on purpose: a plain sweatshirt with a hint of check when closed, and something closer to a hoodie worn over a flannel shirt when open.

Should I line just the hood or the body as well?

Line both if you want the layered look. Lining only the hood gives a little check around the neck; carrying the lining through the body is what makes it look as if there is another shirt underneath.

liningzippedopen
Hood onlya little check around the neckthe reverse of the sweatshirt fabric inside the body
Body and hoodcheck at the hoodcheck down the full front, the layered look
Body, hood and sleevescheck at the hoodcheck down the front and inside the sleeves

A hood-only lining is a legitimate choice. It is a smaller detail, it uses less of the lining fabric and it leaves the body as it would be unlined. But it is a different garment from the one most references for this look show, so it should be a decision rather than a misunderstanding between the brand and the factory.

Do the sleeves need to be lined too?

That is the brand's decision, and it has to be stated. A reference photograph usually shows the check in the body and hood, but it rarely shows what happens inside the sleeves, so a factory working from a photograph has to guess.

Mark it on the brief either way. A lined sleeve carries the check down the arm and makes the inside of the garment consistent. An unlined sleeve leaves the sweatshirt fabric's own reverse inside the arm. Neither is wrong. What causes trouble is a sample that arrives with one when you expected the other, because changing it means another round of sampling.

What changes when a hoodie has a lining?

The garment gains a second fabric, more pattern pieces and more making. Each of those affects the cost, the feel and how the garment behaves in the wash, so each is worth settling on the sample.

Fabric. The lining has its own consumption, and a check adds a matching question: whether the lines have to meet where the two fronts close at the zip, and how the hood pieces are placed on the check. Matching a check uses extra fabric, as the shirt costdown shows on a checked flannel.

Making. A lined hoodie is close to two garments joined at their edges, so there is more cutting and sewing in each piece.

Feel. Two layers drape and move differently from one. Ask for the sample in the actual shell and lining fabrics you intend to use, not a substitute.

Washing. The shell and the lining are different fabrics and may not shrink by the same amount. If they behave differently, the garment can pull or pucker along the joins. Wash the sample before approving it.

How do I brief a factory for a lined hoodie?

Send an open view of the hoodie as well as a closed one, and mark where the lining should go. Include the sleeves on the drawing if you want them lined too.

A closed view on its own shows the outside and the hood, and leaves the factory to infer the rest. The open view is where the lining actually is. Mark it on the body, the hood and the sleeves, name the lining fabric separately from the shell, and say whether the check has to match at the centre front. If you are working from a reference photograph, send it, but treat it as a picture of the look rather than a specification. A photograph shows the check. It does not establish the fibre, the weight or what is inside the sleeves.

What to put in the tech pack

  • Shell fabric and lining fabric, each with its own composition and colour.
  • An open view and a closed view, with the lining marked on the body, the hood and, if wanted, the sleeves.
  • Whether the check matches at the zip, and how it is placed on the hood.
  • The zip itself: chain, gauge, slider and colour, as set out in how to specify a zip.
  • A wash test on the sample before the bulk is approved.

For the rest of the brief, read the guide to small-batch hoodie production. If you have a reference but no production document, request a free tech pack.

Keep reading

Ask us about yours.

Tell us what you want made and we will tell you what it takes before you commit to anything. The quote is free.