What is understitching, and when should a garment have it?
· 3 min read
Understitching sews the seam allowance to the pocket bag or facing a few millimetres from the seam, typically 2 to 3 mm, so the edge rolls under and the bag stays out of sight with no stitching visible from the outside.
On this page
Why does the pocket bag show at the edge of my sample?
Because nothing is holding the seam to the inside. When a pocket bag is sewn to the front panel and turned through, the seam sits right on the edge of the opening, and without something to roll it under, the bag fabric creeps out and shows.
It is a small fault that reads as a cheap garment. On a chino or any garment with front pockets, a strip of pocketing visible at the opening is one of the first things a careful customer notices. The same thing happens wherever a facing or a lining meets an edge: a neckline, an armhole, a collar.
There are three ways to deal with it: press the edge, topstitch it, or understitch it. They are not equivalent.
What is understitching?
Understitching is a second row of stitches, sewn through the pocket bag and the seam allowance together, a few millimetres from the first seam. It sits on the inside, so from the outside of the garment it cannot be seen.
The steps, in order:
- The pocket bag is sewn to the front panel.
- The bag is opened out flat, and the seam allowance is pressed over towards the bag.
- A second row of stitching goes through the bag and the seam allowance together, close to the first seam. The distance is commonly 2 to 3 mm.
- The bag is turned to the inside.
Because the seam allowance is now sewn to the bag, the seam cannot sit on the edge any more. It rolls under, the outside fabric wraps around the edge, and the bag stays out of sight. From the outside there is not a stitch to be seen.
How is understitching different from pressing or topstitching?
Pressing rolls the edge under temporarily, topstitching holds it with a visible line on the outside, and understitching holds it with a line that only shows on the inside. The difference is how long the edge stays put and what the customer sees.
| method | what holds the edge | visible from outside | how it lasts |
|---|---|---|---|
| Pressing only | Heat and steam | No | Relaxes with wear and washing |
| Topstitching | A row of stitches through all layers | Yes, a line along the edge | Holds mechanically |
| Understitching | The seam allowance sewn to the bag or facing | No | Holds mechanically |
A press can roll the edge under for the sample photographs, which is why a sample can look right on the day it arrives and wrong a few weeks later. A pressed edge relaxes with wear and washing. The understitch holds the edge mechanically, because the seam allowance is physically attached to the bag.
Topstitching does the same job from the outside. On jeans and workwear that line is part of the look, and there it is the right choice. On a clean chino pocket, a neck facing or a lining, a visible line usually is not what the design intends, and understitching gives the same hold without it.
Where else is understitching used?
Anywhere a facing or lining has to stay on the inside of an edge. Beyond pocket bags, the standard places are neck facings, armhole facings and collars, plus linings that tend to creep out at an opening.
The principle is identical in each case. The seam allowance is stitched to the piece that should stay hidden, and that piece rolls to the inside.
There is one limit. The stitch cannot get into tight corners, so on collar points it stops a little short, and the corner itself relies on a good press. That is normal, not a fault. If the corner of a collar shows its underside, the press is where to look, and so is the way the corner was trimmed and turned.
How do I check a sample for it?
Look at the pocket openings and the neckline from the outside, with the garment on a hanger and again after a wash. If you can see the bag or the facing at the edge, that edge needs understitching.
Then turn the garment inside out. Understitching shows as a row of stitches on the bag or facing, running parallel to the seam and very close to it. If there is no such row and the edge is held only by pressing, expect it to relax once the garment is worn and washed.
Checking after a wash matters for the reason above. A pressed edge can pass inspection fresh and fail later. A wash test on the sample shows which you have.
How to write it in the construction notes
You do not need to describe the operation. Understitching is a standard term, and a factory will know what you mean as soon as it is written down. Add one line to the construction notes for each place it applies:
- "Understitch the pocket bag to the seam allowance, 2 to 3 mm from the seam."
- "Understitch the neck facing to the seam allowance, 2 to 3 mm from the seam."
- The same for armhole facings, collars and linings where they apply.
Where the design calls for a visible line instead, on jeans or workwear, write "topstitch" with the distance from the edge, so it is a decision rather than a default.
These notes belong in the tech pack before the first sample is made, so the sample is built the way production will be. If you do not have a tech pack yet, Splot writes one free, with no obligation to order. For what to check when the sample arrives, see clothing sample cost and approval.