Ordering and factories

A hoodie tech pack example, section by section

· 4 min read

A hoodie tech pack is a cover page, flat sketches, a bill of materials, a measurement chart with tolerances and a grade rule, construction notes, artwork placement and label positions, and the measurement chart is the part most often sent back, usually because it has no tolerances.

On this page
  1. What is in a hoodie tech pack?
  2. What goes on the cover page?
  3. What should the flat sketches show?
  4. What does a hoodie bill of materials list?
  5. What does the measurement chart look like?
  6. What construction details does a factory need?
  7. Why do factories send a tech pack back?

What is in a hoodie tech pack?

A hoodie tech pack is the document a factory samples, prices and produces from. It holds a cover page, flat sketches, a bill of materials, a measurement chart with tolerances and a grade rule, construction notes, artwork placements, and label and packaging instructions.

Each section answers a question the factory would otherwise have to guess. The example below is a pullover hoodie with a kangaroo pocket, a two-piece hood and a drawcord, in an oversized fit. The figures are a worked example for this article, not a standard, but every section is laid out the way a factory expects to read it.

What goes on the cover page?

The cover page identifies the style and the version. It should let anyone in the factory confirm, in a few seconds, that they are working from the current file.

  • Style name and style number, for example "Hoodie 01".
  • Sample size, here M, which is the size the pattern is made and fitted in first.
  • Colourways, each with a reference the dye house or mill can match.
  • Body fabric in one line, so the cover alone tells the cutter what the garment is.
  • Version number and revision date, and a short note of what changed since the last version.

The version line matters more than it looks. Two files with the same style name and different measurements are a common cause of a wrong sample.

What should the flat sketches show?

Flat sketches are technical drawings of the garment laid flat, front and back, with the hood shown open if its shape is not clear from the front. They show construction, not mood: every seam, stitch, rib, pocket, eyelet and label position, each with a callout.

A callout is a short line on the drawing pointing at a detail, such as "twin-needle topstitch at armhole" or "bartack at both pocket openings". Measurements do not belong on the drawing itself. They go in the measurement chart, where each one has a defined point and a tolerance.

What does a hoodie bill of materials list?

The bill of materials lists everything that goes into one garment, with enough detail to buy it. For each item it gives the material, colour, size, placement and quantity per piece.

ItemExample specificationPlacementPer piece
Body fabric100% cotton brushed fleece, 400 gsm, tolerance 5% either way (380 to 420)Body, sleeves, hood, pocketas marked
RibCotton rib with elastane, colour matched to bodyCuffs, hemas marked
DrawcordFlat cotton cord, colour matched, tipped endsHood channel1
EyeletsMetal, finish namedHood front2
Sewing threadColour matched; fibre namedAll seamsas needed
Main labelWoven, size and fold namedCentre back neck1
Care and composition labelPrinted, wording suppliedLeft side seam1
Hang tag and polybagArtwork and size suppliedPacking1 each

Name the fibre of the thread even if it seems minor. If the garment is later dyed or washed, the thread reacts to it differently from the fabric.

What does the measurement chart look like?

The measurement chart lists each point of measure, how it is taken, the value in the sample size, the tolerance, and the grade to the other sizes. It is the part of the tech pack the finished garment is checked against.

Point of measureHow it is measuredMTolerance
Half chestStraight across, just below the armhole60 cm±1 cm
Body lengthFrom the high point of the shoulder to the hem72 cm±1 cm
Sleeve lengthFrom the shoulder point to the cuff edge60 cm±1 cm
Hem width, relaxedStraight across the hem rib, unstretched52 cm±1 cm
Cuff opening, relaxedStraight across, unstretched9 cm±0.5 cm
Hem rib heightSeam to edge7 cm±0.5 cm
Cuff rib heightSeam to edge6 cm±0.5 cm
Hood heightFrom the neck seam to the top of the hood36 cm±0.5 cm

The tolerance says how far a production piece can sit from the chart and still pass. In this example the large measurements carry ±1 cm and the small ones ±0.5 cm, because a centimetre is a small share of a chest and a large share of a cuff.

The grade rule then sets the other sizes from M. Here the half chest grows by 2.5 cm per size, the body length by 1.5 cm and the sleeve by 1 cm. The rib heights stay the same in every size.

SizeHalf chestBody lengthSleeve length
S57.5 cm70.5 cm59 cm
M60 cm72 cm60 cm
L62.5 cm73.5 cm61 cm
XL65 cm75 cm62 cm

What construction details does a factory need?

The construction page says how each seam is sewn and where it is reinforced. Without it, the factory chooses, and two factories will choose differently.

For this hoodie it would name the seam type for joining the body and sleeves, the stitch used on hems and cuffs, any topstitching and its distance from the seam, and how the hood is joined at the neck. It would say whether the pocket is single or double layer, where it is bartacked, how the drawcord channel is made, and how the eyelets are backed so they do not pull through the fleece.

Why do factories send a tech pack back?

Because something they need to sample or price is missing or contradicts itself. The same gaps come up again and again:

  • Measurements with no tolerances, so nobody can say whether a piece passes.
  • Measurements with no method, so "chest" can mean round the body, across the flat, or across the armhole.
  • Fabric described by feel ("heavy and soft") rather than composition, weight and finish.
  • No rib specification, or rib named without its colour.
  • Artwork with no size, or placement given by eye rather than from a fixed point such as the high point of the shoulder.
  • Two versions in circulation with different numbers.

What to send with the tech pack

Send the tech pack with the quantities by size and colour, the target date and the delivery country, and a reference garment if you have one, marked with what should change. That is enough for a factory to quote and to make a first sample.

If you have a reference but no production document, Splot writes the tech pack free, with no obligation to order: start with a free tech pack. For how a sample is costed and approved, read clothing samples: cost, timing and approval, and for the rest of a hoodie brief, custom hoodie production in a small batch.

Keep reading

Ask us about yours.

Tell us what you want made and we will tell you what it takes before you commit to anything. The quote is free.