Why T-shirt collars go wavy, and how to specify one that lasts
· 4 min read
A wavy collar, known as bacon neck, appears when the neck rib loses its recovery and grows longer than the neckline, and the fix is a little elastane or a denser rib, a taped back neck and a wear and wash test before approval.
On this page
What is bacon neck on a T-shirt?
Bacon neck is the common name for a T-shirt collar that has stretched out and gone wavy, rippling round the neckline like a rasher of bacon. A lot of it comes down to one strip of fabric: the rib band sewn round the neck.
It tends to show up on the tee that gets worn most, which is usually somebody's favourite. That is the reason it matters to a brand. The customer keeps wearing the shirt, and the wavy collar is what they see in the mirror each time they put on your label.
Bacon neck is not only a care problem. Washing and wearing bring it out, but how much and how soon is largely decided by the rib and the way the neck is finished, both of which are written into the specification before production.
How is a T-shirt neckline made?
A tee's neckline is a band of rib knit, cut shorter than the neck opening and stretched to fit as it is sewn on. Because the band is shorter, it pulls the neck in and holds it flat against the body.
Rib is a knit with alternating raised and sunken columns of loops. That structure lets it stretch a long way across its width and then spring back, which is exactly the property a neckband needs.
That only works while the rib still springs back. Once the band loses its tension, nothing pulls the neck in.
Why does an all-cotton neck rib stretch out?
Because cotton recovers less than a rib with some elastane in it. All-cotton rib gives a little each time it is stretched, and does not come all the way back.
So each time the tee is pulled over a head, the collar returns a tiny bit longer. Over many wears the band grows until it is longer than the neckline it is sewn to, and the extra length has nowhere to go but into ripples. That ripple is bacon neck.
Recovery depends on the fibre, on whether there is elastane in the yarn, and on how the rib is constructed. Other things add to the damage:
- Heat. A hot tumble dryer does not help a stretched collar.
- Hanging wet. A wet tee hung by its shoulders puts its weight on the neckline.
- Taking it off by the collar. Pulling the shirt over the head by the neck stretches the band more than lifting it by the back hem.
So the rib explains a lot of bacon neck, not all of it, but it is the largest factor a brand controls.
What should the tech pack say about the neck rib?
Three things: the composition of the neck rib, how the back neck is finished, and a wash test on the sample before approval. Together they address the band's recovery, the seam's strength and the evidence that both are working.
| line in the tech pack | what to write | what it does |
|---|---|---|
| Neck rib composition | Cotton with a little elastane, or a denser rib | Helps the band spring back after each stretch |
| Back neck finish | Taped or bound back neck | Reinforces the neck seam at the back |
| Sample approval | Wear and wash test before sign-off | Shows whether the collar holds its shape over time |
This guide gives no elastane percentage on purpose: a figure that circulates online could not be verified. The right amount depends on the rib and the body fabric. Ask the factory or the mill what they recommend for the rib you are using, and ask them to state it in the specification so it is repeated on reorders.
A taped back neck means a strip of tape is sewn over the neck seam across the back, between the shoulder seams. Bound means the seam is enclosed in a binding. Either one adds support where the neck seam takes strain and also covers the raw seam on the inside.
How do I check a collar before approving the sample?
Wear and wash the sample for a few weeks before you approve it. A new collar looks fine on the first day, so a fresh sample tells you very little about how the neckline will behave after use.
Treat the test as the customer would treat the shirt: wear it, wash it, dry it the way your care label says, and repeat. Then look at the neck against an unworn sample if you have one. Check that the band still lies flat all the way round, that the back neck has not started to ripple, and that the band has not visibly grown relative to the opening.
If the collar has begun to wave within a few weeks of normal use, the production run will do the same, and the fix belongs in the rib or the finish, not in the care instructions. A sample is the cheapest point at which to change either. For how samples are costed and signed off, see clothing sample cost and approval.
What can customers do to keep a collar flat?
Skip the hot dryer, do not hang a wet tee by its shoulders, and take the shirt off by the back hem instead of pulling it by the collar. None of these fix a rib that lacks recovery, but they slow the damage on one that has it.
They are worth putting on the care label or the product page, where they are short enough to be read.
What to put in the tech pack
A collar that lasts is mostly specified, not hoped for. Before the sample goes out, make sure the tech pack covers:
- Neck rib composition, with cotton plus a little elastane, or a denser rib, stated rather than left to the factory's default.
- Back neck finish, taped or bound.
- A wear and wash test on the sample before approval, with the result noted against the sample.
- Care instructions that match what the test showed: no hot dryer, no hanging wet by the shoulders.
If you do not have a tech pack yet, Splot writes one free, with no obligation to order. For the other checks worth making on fabric before it is accepted, read four checks on fabric before you accept it.