Why a reordered fabric colour does not match the first order
· 4 min read
A reorder is dyed in a new bath on a new day, so it lands close to the first lot but not on it, and a small reorder below about 200 metres drifts most because it shares a bath with other fabric.
On this page
Why does a reordered colour not match the first order?
Because the colour was not a recipe held on file. It was the result of one dye bath: one batch of fabric, dyed at one temperature, on one day. A reorder months later is dyed in a different bath on a different day, which makes it a different lot, and a different lot lands close to the first one rather than on it.
The recipe can be identical and the result still moves. That is not the mill being careless. It is how batch dyeing works, and the gap between two lots is something a brand either plans for at the first order or discovers at the second.
The practical consequence is blunt. You cannot reorder a colour in the sense of getting the same thing again. You can order it again and get the nearest match the new bath produces.
What changes between two dye lots if the recipe is the same?
Three things move a lot even when the recipe is unchanged: the water, the fibre's own batch, and how full the dyeing machine is.
| what changes | why it moves the colour |
|---|---|
| The water | The bath is made up fresh each time, and the water on the day is not identical to the water last time |
| The fibre batch | Yarn or base fabric from a different batch takes the same dye slightly differently |
| How full the machine is | A half-loaded bath takes dye differently to a full one |
The first two are largely outside your control. The third is the one brands rarely hear about, and it is the one that catches small reorders.
Why does a small reorder drift more than a large one?
Because a small quantity cannot fill a dye bath on its own. Below about 200 metres you are usually not buying a bath at all; you are taking space in somebody else's.
Take working numbers. A first run used 300 metres of a colour, and it sold out. The reorder is 80 metres. Eighty metres will not fill a bath alone, so it rides along with another customer's fabric, at a load and on a day set by their order rather than yours.
The result is a second drop that does not hang next to the first. It shows up where it is hardest to explain away: a product photograph with both drops on one rail, a stockist who receives both, a customer who buys the same piece twice and notices.
None of this is visible on the purchase order. The reorder is the same fabric code, the same colour name and the same recipe. The difference is in the bath.
What does a lab dip approval actually guarantee?
A lab dip approval approves one swatch from one bath. It sets the target shade; it does not promise that the bulk, or a reorder months later, will match that swatch exactly.
The tolerance a factory usually works to is a grey scale rating, typically 4 or 4-5 out of 5. A rating of 4 is a visible difference under a shop light. Nobody is doing anything wrong at a 4. It is simply the tolerance that was agreed, often without anyone saying out loud that it was a tolerance.
So "approved" has a measured meaning behind it, and it is worth knowing which number your approval rests on before the bulk is dyed. A brand that expects 4-5 and a mill that works to 4 can both be acting in good faith and still end up arguing over the same roll.
How do you protect a colour you expect to reorder?
Either buy all the fabric you will need in that colour at the first order, so it is one dye lot, or write a lot tolerance into the fabric specification and manage each lot as its own batch. The first is the safer of the two.
Book the whole colour at the first order
Buy all the fabric you expect to need in that colour for the season at the first order, including the fabric you will not cut yet. It is dyed together, so it is one lot, and the second drop is cut from the same cloth as the first.
The cost is upfront: money tied up in fabric before you know how the colour sells, and the question of where the uncut fabric is stored and who holds it.
Write a lot tolerance into the spec
If you cannot commit to the whole quantity, write a grey scale minimum into the fabric specification and treat each lot as its own batch. Keep lots separate in stock, mark them on the rolls and on finished goods, and tell customers and stockists which lot they are buying.
The cost here comes later: you accept that lots will differ, and you manage that difference instead of hiding it.
| book the whole colour | write a lot tolerance | |
|---|---|---|
| When you pay | At the first order | At the reorder, if the lot drifts |
| Colour match between drops | One lot, one bath | Within the agreed grey scale rating |
| Main risk | Fabric bought for a colour that does not sell | A second drop you cannot sell next to the first |
| What you manage | Storage of uncut fabric | Lot labelling and separate stock |
One is a line on an invoice now. The other can cost you the reorder.
What to put in the fabric spec and the order
- The approved lab dip reference, and the grey scale rating the bulk has to meet against it.
- The total metres per colour you expect across the season, not only the first run.
- Whether the mill will dye that full quantity as one lot, and who stores any fabric you have not cut.
- For a reorder, the quantity, and whether it fills a bath on its own or shares one.
- Lot numbers on every roll, carried through to the finished stock.
When the fabric arrives, check it before it is cut. Four checks to run on fabric before you accept it covers colour in daylight and the rest. If the colour standard and tolerance are not yet written down anywhere, start with a free tech pack.