Fabric

Why wool itches, and which micron to ask for

· 3 min read

Wool itches when fibre ends are too thick to bend against the skin, from somewhere around 30 microns, so ask for the mean fibre diameter and the comfort factor; most merino sits between 18 and 24 microns.

On this page
  1. Why does wool itch?
  2. What is a micron, and when does wool start to prickle?
  3. How fine is merino compared with other wool?
  4. What is the comfort factor?
  5. Why can wool with a fine average still feel scratchy?

Why does wool itch?

Wool itches because of thick fibres, not because it is wool. The prickle comes from fibre ends sticking out of the yarn: a fine end bends when it touches your skin, and a thick one does not bend, so it pokes.

For most people that is a mechanical effect, not an allergy. The skin is reacting to many stiff points pressing on it rather than to the wool itself. For a brand, the useful consequence is that itch depends heavily on the fibre, and the fibre can be specified.

So two sweaters can both say wool on the label, and one is a base layer you can wear on bare skin while the other only goes on over a shirt. The word on the label is the same. The fibre underneath it is not.

What is a micron, and when does wool start to prickle?

Fibre thickness is measured in microns, usually given as the mean fibre diameter of a lot. Somewhere around 30 microns, a fibre gets too stiff to bend against the skin, and that is where prickle starts.

Sources put that threshold in different places, anywhere from 22 to 30 microns, so treat 30 as a marker rather than a hard line. The direction is not in doubt: the finer the fibre, the more readily it bends, and the less it is felt.

Because microns measure diameter, the differences look small on paper. A few microns can still separate a knit people wear against the neck from one they only wear over something else.

How fine is merino compared with other wool?

Most merino sits between 18 and 24 microns, which is why it can go straight on bare skin. Superfine merino is about 18.5 microns and finer. Many lambswools and Shetland wools run coarser.

WoolTypical fibre diameter
Superfine merinoabout 18.5 microns and finer
Most merino18 to 24 microns
Many lambswools and Shetland woolscoarser than merino

Treat this as a rough guide, not a grading. “Merino” names the breed of sheep, not the fineness of a particular lot of fibre, and “lambswool” and “Shetland” describe where the wool came from rather than how thick it is. None of those words gives you the number that decides how the knit feels. The word is the breed. The number is how it feels.

What is the comfort factor?

The comfort factor is the share of fibres in a lot that are finer than 30 microns. It measures the spread of the fibre rather than the average, and the spread decides how many coarse ends touch the skin.

That matters because a few coarse fibres go a long way. About 5% of fibres coarser than 30 microns is enough for most wearers to call a fabric scratchy. A wool can therefore have a respectable average and still prickle, if the spread is wide enough to leave a tail of thick fibres.

Why can wool with a fine average still feel scratchy?

Because the average hides the coarse tail. Two lots can share a mean diameter and differ in how many thick fibres they contain, and it is the thick ones the skin feels.

A CSIRO-linked study of knitted fabrics found that the share of coarse fibres predicted prickle better than the mean diameter did. That is the case for asking for both numbers: the mean tells you roughly where a wool sits, and the comfort factor tells you how much of it will poke.

A swatch is still worth having. Worn against the inside of the wrist or the neck for a few minutes, it tells you what the numbers predict, in the place where the customer will notice it.

What this means for a knitwear order

  • If a factory quotes you merino, ask for the micron. Ask the spinner for the mean fibre diameter of the yarn you are ordering.
  • Ask for the comfort factor as well, the share of fibres finer than 30 microns, since a fine average can hide a coarse tail.
  • Match the number to the garment: a piece worn on bare skin needs the finer end of the range, while one worn over a shirt can use coarser wool.
  • Keep the figures with the approved swatch, so a later delivery can be checked against them.

Splot's minimum for knitwear is 50 pieces per style. How wool pills compared with a blend is covered in why knitwear pills and how to specify against it. To put the yarn details into a specification, start with a free tech pack.

Keep reading

Ask us about yours.

Tell us what you want made and we will tell you what it takes before you commit to anything. The quote is free.