Construction

How to stop a hoodie drawstring disappearing into the hood

· 3 min read

Ask the factory to tack the drawcord at the hood's centre seam, where it meets the face opening, so each end can only travel halfway and neither can be pulled through.

On this page
  1. Why does a hoodie drawstring pull out?
  2. What is a drawcord tack?
  3. Where exactly should the drawcord be tacked?
  4. Does a tack stop the hood from adjusting?
  5. Are knotted or chunky cord ends an alternative?
  6. How can I check whether a hoodie's drawcord is tacked?

Why does a hoodie drawstring pull out?

Because in a lot of hoodies the cord lies loose in a channel around the hood opening, with nothing holding it in place. Pull one end and the other follows it in, until it disappears through the eyelet.

The channel, often called the tunnel, runs around the face opening of the hood, and the cord passes through it from one eyelet to the other. If nothing fixes the cord to the hood, nothing stops one end from following the other. One firm pull on one side and the far end slips inside. The wearer is then fishing it back out with a safety pin, which is an experience most people know from their own hoodies.

For a brand, this is a small fault with an outsized effect. Nothing is broken, but the garment feels badly made in the customer's hands, and it happens after the sale, at home, where the brand does not see it.

What is a drawcord tack?

A tack is a few stitches through the hood and the cord together, at the top of the hood. It fixes the middle of the cord to the garment, so the cord still slides but each end can only travel halfway.

That is the whole mechanism. With the middle fixed, the cord behaves as two halves, each working its own side of the hood. Pulling the left end tightens the left side; it cannot drag the right end in after it, because the right half is held at the tack. Neither end can be pulled through.

Some hoodies have it and nobody notices, which is exactly the point. A well placed tack is invisible to the wearer until the moment it does its job, and then it is still invisible, because the thing it prevents simply does not happen.

Where exactly should the drawcord be tacked?

At the top of the hood, where the hood's centre seam meets the face opening, above the wearer's forehead. On a tech pack this point is the centre back hood seam, written CB hood.

The position is easy to get wrong because "centre back" sounds as if it means the back of the neck. It does not. The channel runs around the face opening, not around the neck, and the centre seam of the hood reaches that opening at the top of the head. That is where the cord passes the midpoint of its run, and that is where the tack belongs. A tack placed off centre divides the cord unevenly and leaves one side with less cord to pull than the other.

Does a tack stop the hood from adjusting?

No. The cord still slides through the channel, so the hood can be tightened and loosened as before. What changes is that each end has a limit, halfway round, instead of being free to travel the whole length.

In normal wear the limit is rarely reached. It comes into play when someone pulls one side far enough to drag the other end inside, which is exactly the movement the tack is there to stop.

Are knotted or chunky cord ends an alternative?

They do a similar job, as long as they are bigger than the eyelet. An end that cannot fit through the eyelet cannot disappear into the channel.

methodhow it workswhat to check
Tack at CB hood seamfixes the cord's middle, so each end works its own halfthat it sits at the top of the hood
Knotted endsa knot too big to pass through the eyeletthe knot is larger than the eyelet
Chunky cord endsan end piece too big to pass through the eyeletthe end is larger than the eyelet
Nothingthe cord lies loose in the channelexpect lost ends

The approaches can be combined. A tack keeps the cord balanced on both sides; ends larger than the eyelet stop either one escaping. The choice may also come down to the look, since cord ends are visible on the front of the garment and a tack is not.

How can I check whether a hoodie's drawcord is tacked?

Slide the cord. If it stops halfway, it is tacked; if one end keeps travelling while the other shortens, it is loose.

You can do this on your own hoodie, on a competitor's or on a factory sample, in a few seconds and without taking anything apart. On a sample, do it every time, because it is the kind of detail that can be agreed in writing and then missed on the production line. Look at where the tack sits as well. It should be at the top of the hood, on the centre seam, not off to one side.

What to put in the tech pack

It is one line under trims: drawcord tacked at CB hood seam. Add the cord type and the finish on the ends, and check both on the sample and again on the first pieces of the bulk.

If you are developing a hoodie, the same brief has to cover the fabric, the zip and any lining. See how to make a flannel-lined zip-up hoodie and the guide to small-batch hoodie production. A free tech pack can carry the drawcord line with the rest.

Keep reading

Ask us about yours.

Tell us what you want made and we will tell you what it takes before you commit to anything. The quote is free.