How much fabric weight can vary from the spec, and why humidity matters
· 3 min read
Most specifications allow 5% either way, so fabric invoiced at 380 gsm passes anywhere from 361 to 399, provided the sample has rested for a day first, because cotton holds water and a humid room reads heavy.
On this page
How much can fabric weight vary from the spec?
Most specifications allow 5% either way. On a fabric invoiced at 380 gsm, that puts an acceptable delivery anywhere from 361 to 399.
No fabric will read its nominal weight exactly, and it does not need to. Yarn, knitting and finishing all vary a little along a roll and between rolls, so the useful question is not whether the reading is 380 but whether it sits inside the band.
| Nominal weight | Tolerance | Lowest acceptable | Highest acceptable |
|---|---|---|---|
| 380 gsm | 5% either way | 361 gsm | 399 gsm |
A reading only means something against a band both sides agreed to. Five percent is common, not universal, so the figure that applies to your order is the one in your specification. If it is not written there, a disagreement about a reading becomes a disagreement about what was promised.
How do I weigh a fabric sample accurately?
Cut a disc of exactly 100 square centimetres, weigh it on a scale that reads to a hundredth of a gram, and multiply by 100. A disc of 3.8 grams is 380 gsm.
The arithmetic works because 100 square centimetres is one hundredth of a square metre. A round sample cutter takes out exactly that area every time, so the size of the sample is no longer a source of error. The weighing itself takes about ten seconds, at your own desk.
The scale matters more than it looks. On a 100 square centimetre disc, every hundredth of a gram is one gsm, so the whole band from 361 to 399 is 3.61 to 3.99 grams on the scale: less than half a gram wide. A scale that reads only to the gram can catch a large shortfall, but it cannot tell you whether a reading near the edge is inside the band or outside it.
Weigh more than one disc, from more than one place in the delivery, so that one unlucky cut does not decide the result.
Why does humidity change the gsm reading?
Because cotton holds water, and water has weight. Weigh a disc straight off a damp delivery and it reads heavy; weigh it in a dry office and it reads light.
So a reading under spec is not automatically a short delivery. The number on the scale depends partly on the room you weigh it in. A fabric that is genuinely on weight can read light in dry air, and a fabric that is short can be flattered by moisture it picked up in transit or storage.
Neither error is anybody's fault, and both point the same way: control the conditions before you trust a reading, especially one close to the edge of the band.
How do labs condition fabric before weighing it?
Labs let the disc rest for a day at about 20°C and 65% relative humidity before weighing. That lets the fabric settle to a standard moisture level, so that readings taken in different places can be compared.
Most brands do not have a conditioned room. The part that matters most can be done anywhere: cut the disc, leave it to rest for a day before weighing, and note the room's conditions when you do. A reading taken straight out of the box is the one most likely to mislead.
If a result is borderline, or the conversation with the factory is going to turn on it, a reading taken under those laboratory conditions is the one both sides can rely on.
How do I read the result against the tolerance?
Compare the rested reading with the agreed band, not with the nominal number.
| Reading | Against 380 gsm | Inside 361 to 399? | What to do |
|---|---|---|---|
| 372 gsm | about 2% under | yes | pay the invoice |
| 347 gsm | nearly 9% under | no | send the measurement and ask for a price adjustment |
A reading of 372 is below nominal and inside the band. It is a pass, and treating it as a fault would mean asking for more than the specification promised. A reading of 347 is nearly 9% under. It is well outside a 5% band, and at that point it is not an opinion any more.
What do I do when the fabric reads under weight?
Send the factory the number and ask for a price adjustment. A weight outside an agreed tolerance is a quantity discrepancy with a figure attached to it, which makes it a straightforward conversation.
State what you measured, how you conditioned the disc, what equipment you used and where in the delivery the discs came from. The more of the method you can give, the less room there is to argue about the reading rather than the fabric. A factory working with a mill can take that measurement back up the chain, to where the fabric was made.
Do this before you pay the invoice. A measurement is easiest to act on while the payment is still open.
What to write into the fabric specification
- The fabric weight in gsm.
- The tolerance, for example 5% either way, written out as a band (for 380 gsm, 361 to 399).
- How weight is measured: a 100 square centimetre disc, a scale reading to a hundredth of a gram, more than one disc.
- How samples are conditioned before weighing, for example a day's rest at about 20°C and 65% humidity.
Agree all of it before the order goes out, not after the delivery. The basic weighing check, with the other three tests worth running on a delivery, is in four checks to run on fabric before you accept it. Why weight alone does not describe a fabric is covered in what GSM does and does not tell you about a heavyweight tee.